The calculator will indicate the number of 60 or 80 pound bags of QUIKRETE® Mortar Mix you need to construct your project with a 3/8 inch mortar joint. (All yields are approximate and do not include allowance for uneven subgrade, waste, etc.).
Also asked, how much concrete do I need for a post hole?
Related To:
- The general rule of thumb when setting a post is that the depth of the post's hole needs to be 1/3 to 1/2 of the actual above-ground height of the post.
- Now that you've determined the size of the hole you'll need, you can use the chart below to determine how many 50-pound bags of concrete you'll need.
Also, how many bags of quikrete do I need for a 4x4 post? QUIKRETE® CONCRETE MIXES CALCULATOR: Enter the size of the slab you want to build in square feet. The calculator will indicate the number of 60 or 80 pound bags of QUIKRETE® Concrete Mix you need to build a 4″ or a 6″ slab.
Regarding this, how much area does a 50 lb bag of quikrete cover?
One 50-pound bag of Quikrete Fast Setting Concrete Mix yields about . 375 cubic feet. For example, if you need to cover 33.333 cubic feet, using 60-pound bags of concrete, divide 33.333 cubic feet by . 45 cubic feet to get 74.07 total bags of concrete.
How much does a bag of cement cost?
A bag of cement, portland cement, 94 pound in the USA, less in Canada, used with sand, rock and water to make concrete runs right at $10 around here. Prices vary of course.
Related Question Answers
Is 2 feet deep enough for fence posts?
The minimum depth that you should dig your fence post holes for panel sections is 2 feet. A general formula is to dig the holes one-third to one-half of the post's aboveground height. The deeper you dig the holes, the more stability your fence has, but you must also purchase longer posts.How many bags of cement do I need for a post hole?
Estimating 60-lb Bags of Fast-Setting Concrete Mix
| 3-in Post Diameter / 9-in Hole Diameter | 6-in Post Diameter / 18-in Hole Diameter |
| Hole Depth in Inches | Number of Bags needed Per Hole | Number of Bags needed Per Hole |
| 10 | 1 | 3 |
| 12 | 1 | 4 |
| 14 | 1 | 4 |
How deep should fence posts be set in concrete?
600mm
How deep should a 12 foot post be in the ground?
In general, holes should be at least 3 feet deep for posts that extend 8 feet or more above ground level. Posts that extend 6 feet above ground level should have holes at least 2 1/2 feet deep.Do fence posts need concrete?
Concrete is the most secure material for setting fence posts, especially if you have sandy soil. Gravel may be okay with dense, clay-heavy soil, but in looser soil, concrete is the only thing that will truly keep your fence posts stuck in place.How do you install a 4x4 post on concrete?
Drill holes in the concrete of the right diameter for lead shields using a masonry bit in a hammer drill. Insert lead shields into the holes in the concrete. Use lag bolts or screws to attach the metal post bracket to the concrete. Insert the wood post in the post bracket, and screw or nail it in place.How deep should a 6x6 post be in the ground?
Your local building codes should specify a recommended depth for post holes in your area. For an 8-foot tall structure like this one, plan on about two-feet in depth. The depth of your hole should be about 1/4 of the height of your post. For a 6x6 post, the diameter of the holes should be about 12 inches square.How big of a hole do I need for a 4x4 post?
Dig an 8"-diameter hole at least 6" deeper than your area's frost line for each 4x4 post, using a power auger, hand auger, or post-hole digger. A 6x6 post requires a 10"-diameter hole. Shovel a 6" layer of gravel into the hole to provide drainage.Is quikrete as strong as concrete?
Concrete is a mixture of water, cement, sand just like mortar. However concrete also has gravel and other coarse aggregates that makes it stronger and more durable. Concrete has a low water-to-cement ratio and is a thinner consistency than mortar. One of the concretes we sell is the Quikrete Fast Setting Concrete Mix.How many bags of concrete do I need for a 10x10 slab?
Using a Concrete Calculator You'll also get the number of 40-pound, 60-pound, or 80-pound bags of concrete are needed for the project. For example, a 10′ x 10′ slab that is 4″ thick will need an estimated 1.23 yards3 or 75 60lb bags of concrete and will cost roughly $140.How do you mix 50 pounds of quikrete?
Pour water into the dry mix until the powder is saturated with water. Depending on soil conditions, this will require about 1 gallon (3.8 L) of water per 50 lb (22.7 kg) bag. For holes deeper than 2' 6" (0.8 m), place the material in lifts of 2' 6" (0.8 m) or less to allow water to soak all the way through.Can I pour concrete over old concrete?
If the existing concrete is in good shape structurally, you can pour new concrete over it to freshen it up. Proper prep work is key to success when layering new concrete over old. If the existing concrete is in good shape structurally, you can pour new concrete over it to freshen it up.How many bags of quikrete make a yard?
How many 80 lb bags of concrete do I need for 1 yard? The finished volume of an 80# bag of Sacrete or Quikrete (pre-mixed cement, sand and gravel) is 0.6 cubic foot (stated on the bag). There are 27 cubic feet in a cubic yard. Dividing 27 cubic feet by the volume of the bag will give you the number of bags you need.What is the difference between concrete and cement?
What is the difference between cement and concrete? Although the terms cement and concrete often are used interchangeably, cement is actually an ingredient of concrete. Concrete is a mixture of aggregates and paste. The aggregates are sand and gravel or crushed stone; the paste is water and portland cement.How much water do I need for a 60 pound bag of quikrete?
Pour dry mix into the hole until it is approximately 3" - 4" (76 - 102 mm) from the top. 3. Pour water into the dry mix until the powder is saturated with water. Depending on soil conditions, this will require about 1 gallon (3.8 L) of water per 50 lb (22.7 kg) bag.How many 60 pound bags of cement does it take to make a yard?
60 pound bag yields .017 cubic yards. 80 pound bag yields .022 cubic yards.How much water do you put in a 60 pound bag of quikrete?
MACHINE MIXING INSTRUCTIONS For each 80 lb (36.3 kg) bag of QUIKRETE® Concrete Mix to be mixed, add approximately 6 pt (2.8 L) of fresh water to the mixer.How long should quikrete cure before removing forms?
two days
How long does it take for quikrete to harden?
Regardless of the application, QUIKRETE Fast Setting Concrete Mix sets in 20 to 40 minutes and reaches 400 psi in two hours, allowing the post or concrete slab to be used right away. 
